GT SYSTEM 600 AUTOMATIC FIRE DOOR
USING THE GYRO SWING
SPRING CLOSE OPERATOR
SUGGESTED ARCHITECTURAL SPECIFICATIONS
SECTION 8
AUTOMATIC ENTRANCE SYSTEMS

PART 1-GENERAL

1.01 DESCRIPTION

A.             Furnish and install automatic entrance equipment as indicated on drawings and as specified.

B.            Related work specified elsewhere.

1.             Electrical Supply: Section _______

2.             Floor Preparation: Section _______

1.02 QUALITY ASSURANCE

A.             Manufacturer's Qualifications:

Products specified shall be represented by a factory authorized and trained distributor. Distributor shall maintain a parts inventory and trained personnel capable of providing service.

B.             Requirements of Regulatory Agencies:

1.             Underwriters Laboratory, Inc. (UL): Automatic entrance and/or exit doors shall be a UL listed system in guide FDDR and/or guide FUXV.

2.             National Fire Protection Association (NFPA); Automatic Fire Door Assemblies shall be approved for use with UL listed door frames and latching devices as designated by NFPA 101 and NFPA 80.

C.             All automatic equipment to comply with ANSI A156.10.

D.        Gyro Tech equipment as manufactured by NABCO ENTRANCES, INC. has been specified and shall be quoted as the base bid. Other systems may be quoted along with information specifically detailing the differences from the following specification.

1.03 SUBMITTALS

A.        Shop drawings showing complete elevations, details and method of anchorage to location; installation of hardware; size, shape, joints and connections; and details of joining with other construction.

B.        Templates and diagrams and/or shop drawings as needed shall be furnished to fabricators and installers of related work for coordination of operators with doors, frames, hardware, concrete work and other work.

C.        A copy of appropriate manual shall be provided to owner's engineer upon completion of installation.

1.04 WARRANTY

A.        Warranty of power operators, controls and labor provided by automatic door equipment installer against defects in material and workmanship at no cost to owner, for a period of one year from date of substantial completion. Provide warranty to owner after completion of installation.

1.05 COMPLIANCE

A.        A completed American Association of Automatic Door Manufacturers (AAADM) form shall be submitted as proof of compliance with ANSI 156.10 Standard for power operated pedestrian doors. Door(s) shall be inspected and form shall be signed by an AAADM certified inspector prior to placing door(s) in operation.

PART 2-PRODUCTS

2.01 APPROVED MANUFACTURER

A.             Automatic entrance equipment and controls shall be distributed by:

Ontario Door Controls

1350 Matheson Boulevard East

Unit 16, Mississauga

Ontario, Canada.

Phone: (905) 238 9222

Fax    : (905) 238 9279

e-mail: products@automaticdoorsystems.com

Website: http://www.automaticdoorsystems.com

2.02 AUTOMATIC SWING DOOR SYSTEM

A.        GYRO TECH System 600 (surface applied) automatic swing door system for automating fire doors as indicated on door schedule and details.

B.        Mode of Operation: Spring-Close. Gyro-Swing operator shall open door by energizing motor and shall stop door by electrically reducing voltage and stalling motor against mechanical stop. Door shall close slowly by means of spring energy, and closing force shall be controlled by gear system and motor being used as dynamic brake without power. System shall also operate as a manual door in event of power failure. Manual operation shall require less than 15 lbs. force applied to door stile. Opening and closing speeds shall be adjustable. Door operation shall not require any fluids or gases under pressure to be used in opening and closing of door.

C.             Components:

1. Operator Housing

2. Gyro-Swing Power Operator

3. Electronic Control

4. Soft Start

5. Connecting Hardware

6. Accessory Package (single or double doors)

1a)             Operator Housing: GYRO TECH Housing shall be 5-1/2" (139.7 mm) wide by 5" (127.0 mm) high aluminum extrusions with finished end caps and shall be prepared for mounting to new or existing door frames. All structural sections shall have a minimum thickness of 0.146" (3.7mm) and shall be fabricated of 6063-T5 aluminum alloy.

1b)             Finish: Aluminum shall have a standard finish of AA-M12-C22-A41 (204 R1) or AA-M12-C22-A42 (dark bronze). Black and special finishes available upon request.

2)         Gyro-Swing Power Operator: Completely assembled and sealed unit which shall include helical gear-driven transmission, overriding clutch (to provide easy manual operation. spring-close). mechanical spring and bearings, all located in cast aluminum housing and filled with special lubricant for extreme temperature conditions. Attached to transmission system shall be a DC shunt-wound permanent magnet motor with sealed ball bearings. Motor shall operate from 115-volt supply and require less than 5 amps at full power stall. Complete unit shall be resilient mounted with provisions for easy replacement, without removing door from pivots or frame.

3)         Electrical Control: Self-contained unit including necessary transformer, relays, rectifiers, and other electronic components for proper operation and switching of Gyro-Swing power operator. Relays shall be plug-in type for individual replacement. All connecting harnesses shall have interlocking plugs. Controls shall also include time delay for normal cycle. Control shall include safe-swing circuit as optional switching which automatically limits power and slows door when approached from passive side.

4)         Soft Start: Energy limiter shall be a modular electronic current control for the purpose of controlling torque to limit stress on entire entrance package.

5)         Connecting Hardware: Connect conversion unit (CU) drive arm to inswing door with a urethane covered roller, which shall ride in a track fabricated of 6061-T6 aluminum alloy attached to the top door rail where required for pull-type operation. Outswing doors shall be connected to operator by a two-piece drive arm with self-aligning rod ends and connecting door bracket for push-type operation.

6)         Accessory Package: Provide one GYRO TECH UL listed fire door accessory package for each door consisting of:

6a)             Latch Mechanism (retractor) (double door only)

6b)             Power Reset Box (double door only)

6c)             Power Box (single door only)

6d)             Caution Labels

NOTE: Double Doors UL listed only with Von Duprin 8827-F Surface applied, UL Listed Exit hardware. Single Door UL Listed only with Von Duprin 3041 Electric Strike and Von Duprin 8875-F Mortise Lock

2.03 ACTIVATING DEVICES

A.        Wall Switches: 6" (152.4 mm) diameter stainless steel, surface or plain, as manufactured by NABCO ENTRANCES, INC.

B.             Carpet Activators: Of sizes and colors as required shall be manufactured by NABCO ENTRANCES, INC.

C.             Optional activators are available - See Product Catalog.

PART 3-EXECUTION

3.01 INSTALLATION

A.        Automatic door equipment shall be installed by factory-trained installers in compliance with manufacturer's recommendations and approved shop drawings.

3.02 CLEANING AND PROTECTION

A.        After installation, clean framing members as recommended by manufacturer. Aluminum surfaces in contact with masonry, concrete, and steel shall be protected by use of neoprene gaskets where indicated, or a coat of bituminous paint to prevent galvanic or corrosive action. Advise general contractor to protect unit from damage during subsequent construction activities.

* COVER NOTE TO SPECIFICATION WRITER

Indicate under appropriate Section the following work by others.

ELECTRICAL INSTALLER shall furnish and install all conduit and electrical wiring for activating devices and door operators. A minimum of 5 amperes, 115-volt, A/C, 1-phase circuit shall be furnished of each door operator, terminate and connect to operator control panel in operator housing.

CONCRETE INSTALLER shall prepare floor at location of automatic entrance system to accommodate the surface or recessed electric switch mats as indicated on drawings.